Contact USA Rep Organizations In Your AreaSee List on the Contact US tab
Contact USA Inside SalesCatherine Topar
Ph: 203-334-7537
Fx: 203-334-7792
Email: ctopar@e-jpc.com
Product NavigatorSearch By Specification Search By Keyword
Shop
Request Information
  • Motors are designed in flat shape and in light weight
  • A special magnetic circuit design was employed newly. By this design, these motors are in flat shape, and in lighter weight than conventional standard AC motors.
  • This series have 61 mm² (2.4 in²). 80 mm² (3.1 in²). 90 mm² (3.5 in²) Flange sizes.
  • Compact designed Driver
  • "Palm Mini PLUS" Type is the smallest, (for 6 W - 40 W)
  • "Simple" Type is a driver of components mounted on a PCB. (for 6 W-15 W)
  • "High power Simple" Type Low-cost circuit-board type driver. (25 W\40 W)
  • Wide Ranged Speed Control
  • Wide range (200 r/min - 2500 r/min), stepless speed control. "High power Simple" Type. (200 r/min - 2000 r/min)
  • Very steady characteristics (Feed back control employed).
  • Speed pulse output
  • Speed pulse output can be used for speed monitoring, simplified position control...
  • "Palm Mini PLUS" Type: 30 ppr
  • "Simple" "High power Simple" Type: 5ppr dual signal (120° phase difference)
  • Direction of rotation signal output
  • Direction of rotation can be monitored by this signal. ("Simple" type needs an external circuit.)
  • Alarming
  • At an over-load condition, the motor stops and an alarm signal is output.
  • Gear Head
  • Low-cost gear head for FY series is also available.
  • Rotor Cover (option) available
  • An aluminum heat sink (size: 200 mm x 200 mm, thickness: 2 mm or more) is required.
Unit of Measure

Type

 N/A High Power Simple Motors

Product Type

 N/A High Power Simple Type Motor

Series

 N/A FYD

Motor Frame Size

 N/A 90 x 90 mm3.5 x 3.5 in

Number of Poles

 N/A 10

Shaft Specification

 N/A Pinion Shaft

Rated Voltage

 N/A 24 V

Rated Voltage

 N/A 24 V

Rated Output

 N/A 40 W

Rated Torque

 N/A 250 mN·m36 oz·in

Rated Speed

 N/A 1500 r/min

Speed Control Range

 N/A 200 to 2000 r/min

Max. Instantaneous Torque (in 5 sec.)

 N/A 28 mN·m (1500 r/min) 43 oz·in (600 r/min)

Max. Instantaneous Torque at 1500 r/min (in 5 sec.)

 N/A 28 mN·m

Max. Instantaneous Torque at 600 r/min (in 5 sec.)

 N/A 43 oz·in

Speed Setting Method

 N/A (1) Speed setting by external speed setter (Sold separately: model code Q-R10KB) (2) Speed setting by external voltage supply 0~10V

Speed Variation (Against Load ±1%)

 N/A 0~rated torque at rated voltage and speed

Speed Variation (Against Voltage ±1%)

 N/A DC 24 V ± 10 % at rated speed, no load

Speed Variation (Against Temperature ±1%)

 N/A 20 ± 20ºC at rated voltage and speed, no load

Input Signal

 N/A H : Open collector L : GND (0~0.8V) Run, Brake, F/R IN, Alarm RST

Output Signal

 N/A Alarm, HU Out, HV Out Open Collector Output DC 30 V Max. 10 MA Max.

Speed Pulse (Pulse/Revolution)

 N/A 5

Max. Average Current Rated

 N/A 3.4 A

Max. Peak Current Rated

 N/A 10 A

Protection Functions

 N/A Over load protection
When an exceeding torque than rated is applied to motor for more than about 5 sec, Stop motor and outputs "L" from "ALARM"

Operation Temperature

 N/A 0~40ºC (no condensation) continuous duty. The motor flange surface temp. must be 80ºC Max. (Ambient temperature 40ºC without heat sink)

Motor Dielectric Strength

 N/A Withstand for 1 min. under AC500V 50Hz (Between case and coil)

Motor Insulation Resistance

 N/A 10 MO MIN. (Between case and coil by DC500V tester)

Note

 N/A Minimum Order Quantity May Apply

Rated Power

 N/A 40 W

Peak Current

 N/A 10 A


FY9S40-D3_FYD940PD3-ST-CURVE.jpg


Distinguishing Features

Model Code